High Quality for TU-1C07 thermal wax actuator for air conditioner and compressor for Mecca Manufacturer
Short Description:
Product Detail
Product Tags
High Quality for TU-1C07 thermal wax actuator for air conditioner and compressor for Mecca Manufacturer Detail:
1. Operation Principle
The Thermostatic Wax that has been sealed in shell body induces expansion by a given temperature, and inner rubber seal part drives its handspike to move under expansion pressure to realize a transition from thermal energy into mechanical energy. The Thermostatic Wax brings an upward movement to its handspike, and automatic control of various function are realized by use of upward movement of handspike. The return of handspike is accomplished by negative load in a given returned temperature.
2. Characteristic
(1)Small body size, occupied limited space, and its size and structure may be designed in according to the location where needs to work.
(2)Temperature control is reliable and nicety
(3)No shaking and tranquilization in working condition.
(4)The element doesn’t need special maintenance.
(5)Working life is long.
3.Main Technical Parameters
(1)Handspike’s height may be confirmed by drawing and technical parameters
(2)Handspike movement is relatives to the temperature range of the element, and the effective distance range is from 1.5mm to 20 mm.
(3)Temperature control range of thermal wax actuator is between –20 ~ 230℃.
(4)Lag phenomenon is generally 1 ~ 2℃. Friction of each component part and lag of the component part temperature cause a lag phenomenon. Because there is a difference between up and down curve of traveling distance.
(5)Loading force of thermal wax actuator is difference, it depends on its’ shell size.
Product detail pictures:
"Sincerity, Innovation, Rigorousness, and Efficiency" may be the persistent conception of our organization for that long-term to establish jointly with customers for mutual reciprocity and mutual gain for High Quality for TU-1C07 thermal wax actuator for air conditioner and compressor for Mecca Manufacturer, The product will supply to all over the world, such as: Paraguay , moldova , Florence , We've been persisting in the business essence "Quality First, Honoring Contracts and Standing by Reputations, providing customers with satisfying products and service. " Friends both at home and abroad are warmly welcome to establish everlasting business relations with us.
In this Episode of the Project 240 we take on the issues of the car not warming up, the radiator leaking, and some weird idle problems. All in all, a new Isis 60°C thermostat was put in, Prestone coolant mixed 70/30, new 93-95 Altima MAF, new IACV, new air filter, and lastly a used S13 manual ecu.
Looking back at the footage it looks like most likely the second idle issues was probably caused by the auto ecu. Oh well though, what’s done is done and everything’s taken care of in the end.
Hope you guys enjoy!
Merchandise : https://offbeatgarage.com/
Instagram: offbeat_garage
Facebook: https://www.facebook.com/OBGarage
Just a guide to fitting new thermostat and replacing antifreeze in the Fiesta fitted with the 1.3 Endura-E OHV lump.
Because the heater valve had failed I drained and flushed out the cooling system as new heater valves dislike dirty coolant plus any disturbances of the hoses & thermostat etc normally cause flakes and rust particles to dislodge and float about. (these engines use iron block & head)
I also fitted a new thermostat as the old one was showing signs of failing in open position which was making engine run cooler than it needed. The cool running engine affected fuel economy which had dropped to 41 mpg from 46.6mpg. Plus the thermostat housing leaked which dripped onto number one spark-plug which started to rust around the plug which then absorbed water which then affected plug operation plus made it difficult to remove. Spark plugs can seize solid in these iron heads (Something to think about if your Endura-E Fiesta or Ka has coolant leaks from thermostat).
Although not shown in the video, I added coolant straight into the head before thermostat was fitted so I knew head & block had coolant present. Easy to add coolant this way as the thermostat is mounted horizontally which means you just add antifreeze until level reaches just below where ‘stat sits. Then once ‘stat housing is secured, you slowly add coolant into reservoir in usual way. Another method is to wedge the thermostat open with dissolvable tablet which allows coolant to flow into engine when filling. Some thermostats have small bleed holes which helps filling but also allows some coolant to flow in the event that it fails in closed position. A thermostat that has failed shut means hot coolant from block & head cannot flow to radiator for cooling. Another reason to look after your car’s cooling system.
