Professional Manufacturer for TU-1K01 thermal wax actuator for electric switch valve to India Manufacturers

Professional Manufacturer for
 TU-1K01 thermal wax actuator for electric switch valve to India Manufacturers

Short Description:

Product Detail

Product Tags

We take "customer-friendly, quality-oriented, integrative, innovative" as objectives. "Truth and honesty" is our administration ideal for Electric Actuator Limit Switch , Automatic Temperature Controller With Cooling System For Car , Wax Actuator Greenhouse , We always regard the technology and customers as the uppermost. We always work hard to create great values for our customers and offer our customers better products & services.
Professional Manufacturer for TU-1K01 thermal wax actuator for electric switch valve to India Manufacturers Detail:

1. Operation Principle

The Thermostatic Wax that has been sealed in shell body induces expansion by a given temperature, and inner rubber seal part drives its handspike to move under expansion pressure to realize a transition from thermal energy into mechanical energy. The Thermostatic Wax brings an upward movement to its handspike, and automatic control of various function are realized by use of upward movement of handspike. The return of handspike is accomplished by negative load in a given returned temperature.

2. Characteristic

(1)Small body size, occupied limited space, and its size and structure may be designed in according to the location where needs to work.

(2)Temperature control is reliable and nicety

(3)No shaking and tranquilization in working condition.

(4)The element doesn’t need special maintenance.

(5)Working life is long.

3.Main Technical Parameters

(1)Handspike’s height may be confirmed by drawing and technical parameters

(2)Handspike movement is relatives to the temperature range of the element, and the effective distance range is from 1.5mm to 20 mm.

(3)Temperature control range of thermal wax actuator is between –20 ~ 230℃.

(4)Lag phenomenon is generally 1 ~ 2℃. Friction of each component part and lag of the component part temperature cause a lag phenomenon. Because there is a difference between up and down curve of traveling distance.

(5)Loading force of thermal wax actuator is difference, it depends on its’ shell size.


Product detail pictures:

Professional Manufacturer for
 TU-1K01 thermal wax actuator for electric switch valve to India Manufacturers detail pictures


Quality First,and Customer Supreme is our guideline to provide the best service to our customers.Nowadays, we are trying our best to become one of the best exporters in our field to meet customers more need for Professional Manufacturer for TU-1K01 thermal wax actuator for electric switch valve to India Manufacturers, The product will supply to all over the world, such as: San Diego , Accra , Chicago , Our items have national accreditation requirements for qualified, high quality products, affordable value, was welcomed by people today all over the world. Our goods will continue to enhance within the order and look forward to cooperation with you, Should any of these products be of interest to you, please letus know. We are going to be content to offer you a quotation up on receipt of your detailed needs.



  • In this video we show How to replace the oxygen (O2) sensor also known has Air Fuel Ratio sensor on the Nissan Frontier V6 (3300 – VG33E) engine.Here you will see the difference between Bank #1 (right side)and Bank #2(left side) heated (4-wire) oxygen sensors. Replacing the oxygen sensor every 60-70,000 miles is an effort to help conserve fuel/gasoline.The oxygen sensor are not the only device to harness against waste consumption. The coolant temperature sensor at the thermostat housing reports to the computer, the computer commands the cooling fans through the fuel/relay box. Some model will be equipped with dual cooling fans. One for normal operation is the 1st fan. The 2nd fan is for air condition operation and over-heating conditions. If the Tstat remain stuck “close” the two fan will operate and coolant will overflow in its reserve container. The Tstat ONLY control engine temperature. The fans operation and gauge help radiates any heat or over heating base on ambient air temperature and operator.

    The oxygen sensor is a state EPA “enviromental term” all so known has a EGT – exhaust gas temperature sensor sends millivoltage(data) to the ecm – engine control module for fuel injector control and its flow rate(impedeance). The oxygen sensor key roll is to measure the combustion flame/temperature .the ideal temperature for anything above 75% throttle is .870mv – .900mv output at the exhaust gas temperature/oxygen sensor. The oxygen(o2) sensor also work in conjuction with the Mass Air Flow Meter/sensor for fuel injector control. So the oxygen sensor can also be conside a Air Fuel Ratio sensor and the Mass Air Flow meter is mounted on the intake manifold duct.

    M18 sensors – Install finger tight then 1/2 – 3/4 turn with wrench/ O2 sensor socket.26-33ft. lbs
    M12 sensors – Install finger tight then 3/4 – 1 turn with wrench / O2 sensor socket.13.2-17ft. lbs.

    APPLICATION: 2003 NISSAN FRONTIER EX, Xterra
    3300 CC ENGINE 4X4

    PLEASE – RATE – COMMENT AND SUBSCRIBE.

    * DO NOT drop or use an oxygen sensor that has been dropped as this may have caused shock damage to the ceramic cell.
    * DO NOT use any compound on or around the sensor unless labeled as oxygen sensor friendly products.
    * DO NOT use impact wrench or conventional socket type wrench to install sensor.
    * DO NOT allow sensor or lead wire to touch exhaust manifold or any other hot component.
    * DO NOT expose this product to water,oil,windshield cleaner, anti-corrosion oil,grease,terminal cleaner, etc.
    * DO NOT use leaded fuels, silicone or metal based additives
    * DO NOT store under high humidity conditions will promote rusting.
    WARNING : Anti-seize compound may cause irritation to the skin or eyes. In case of contact, wash affected area with soap and water. In case of eye contact, Flush with water for 15 minutes. If irritation persists, consult a physician. If swallowed, DO NOT induce vomiting.

    KEEP OUT OF REACH OF CHILDREN.



    Rotork Fluid Systems – Skilmatic range of actuators offer a unique and reliable solution for electric fail safe and modulating control for both quarter turn and linear valves and dampers.

    For more information contact:
    CTi Controltech
    22 Beta Ct.
    San Ramon, CA 94583
    Phone: 925-208-4250
    Fax: 925-208-4251
    Email: contactus@cti-ct.com
    www.cti-ct.com

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Plane

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Truck

    WhatsApp Online Chat !