Wholesale 100% Original TU-1F06 thermal wax actuator for thermostatic automatic water drain valve to Swiss Factories

Gary Bunzer, the RV Doctor explains the benefits of Hatchlift gas hydraulic springs for RV storage compartment doors.

***VISIT OUR SPONSORS***
https://www.traderadiators.com | https://www.grahamplumbersmerchant.co.uk | https://www.buteline.com/uk | https://www.adey.com | https://celebrate200.co.uk

This video covers s plan heating systems and 2 port valves. This includes their plumbing, their wiring, how they are controlled with time clock programmers and thermostats. For more information visit https://www.plumberparts.co.uk

We all have dreams. Some of them are nightmares, some of them aren’t. But then suddenly, out of nowhere, you wake up and I arrive like a bolt out of the blue to tell you about today’s plumberparts.co.uk video. We’re gonna look at S Plan systems today and the 2 port valve that’s absolutely integral in an S Plan system. So get ready for the wildest journey of your plumbing life. Let’s just go. So an S Plan heating system is just another way of controlling where hot water goes from the boiler. It can either go to the indirect hot water coil on the cylinder to heat hot water up that’s gonna come out the taps, or it can be diverted off to heating radiators or you can have another valve that diverts off to underfloor heating or even another zone for another radiator, all individually controlled by different thermostats and time clocks.
Today we’re gonna look at the very simplest type of S Plan that you can have. That is, we’ve got one valve here that goes off to the hot water cylinder and one valve here that goes off to the radiators. But before we start, as ever, don’t do any work on electrics if you’re not happy and competent and you don’t have an electrical tester. Always make sure everything’s turned off. Always, before you remove a wire or anything like that test and make sure it’s dead, okay? Because otherwise that how you’ll end up. Dead!
First, let’s have a little wee look at the electrics. So with this cover off, here. Now as you can see, sometimes you’ll go to places and the wiring’s just bonkers. You know, look at that, you might think, “God, where does everything go?” But if you isolate each one like we did on the 3 Port system that I showed you a few weeks ago in the videos, we’ll be able to find out where to remove each wire and where to put the new one in for the new valve. Get yourself a bit of paper and write down everything, every colour, and what block it goes to, and where it runs off to, okay? Now, there is a common principle with all control valves, that they need to be open and signal the boiler only once they’re open to tell the boiler and the pump to come on. If that wasn’t there, the boiler and pump could come on with the valves shut and have nowhere to dissipate their heat, could crack boiler sections and cause leaks and basically a whole hubbub of hell. Fortunately, all the manufacturers have thought of this, so when you do your wiring, you have your earth, your neutral, then you have a live feed to the motor itself so when the thermostat calls for heat and everything it will send a live to this and the motor will motor around, and then it has two wires left. Now, it’s a switch, basically, that’s all it is. There’ll always be a constant live to this. This is why when you need to test for electrics in these things you need to be careful and make sure the constant permanent live is dead, cause it’s a switched live. The only way you’ll ever do that is to wire set the whole system electronically by turning it off and removing the fuse. Now, you have the live supply, you have the permanent live comin’ in on one wire. When the valve opens up, it touches a smaller marker switch and sends a live back down this wire to the boiler and the pump to tell them to come on. It’s the same on all these valves, okay? Sometimes the wires on different valves are different colours, but generally nowadays they’ve tried to make them so they’re all the same so it’s easier for you to change. If it is different, have a little look at the book that was supplied with the valve and make sure the wires go in the right place, then. Let’s have a look at this S Plant system in situ. We’ll also describe that at the office in a second. We have our boiler flow coming from here. It goes up there, just across the top to the pump, which you can see just here, and then it comes down to this T here. Now it can either go off by this valve, off to the hot water cylinder to heat the hot water or by the faulty valve that we’re removing to the heating system. That’s basically how an S Plan system works. They’re generally controlled by a programmer and a series of thermostats. The good thing about an S Plan system is you can have as many different zones as you like. So you can have, as I said, underfloor, different radiator zones, different cylinder zones, things like that, which make it a lot easier to control the services in your home.
Let’s just have a quick look, schematically, about how these systems work. Imagine we have our boiler here, with our pump flowing water in that direction.