2017 Good Quality Thermostatic Wax Linearity Series Export to America
Short Description:
Product Detail
Product Tags
2017 Good Quality Thermostatic Wax Linearity Series Export to America Detail:
The characteristic of Thermostatic Wax consists of its volume expansion amount can reach up to 13 ~ 15 % when it is heated from solid to liquid. We use this characteristic, when it is heated to a solid-liquid transformation, its’ heat energy can translate into mechanical energy. Thermostatic Wax has been widely applied to temperature auto regulation of thermal-driving and various thermal-starting devices.
For example, automobile thermostat has been most widely well known, it has cylindrical seal part that loads some Thermostatic Waxes inside. To realize automatic temperature control, it was designed by a special technical specification for the solid-liquid transformation of Thermostatic Wax. When the cylindrical part is heated, Thermostatic Wax in the part is also heated and making a solid-liquid transformation expansion, Thermostatic Wax pushes thermostat’s itself handspike to open the valve. When the cylindrical part gets cold, Thermostatic Wax also cooled and start to shrink, Thermostatic Wax pushes itself handspike back to original situation under the return load force to close up the valve to realize automatic temperature control.
Depending on the main principle of Thermostatic Wax, The developed thermal driving devices and thermostats have been widely applied to automobile thermostat, automobile temperature-control switch for electric fan, various engines cooling water temperature auto controller, lubricant oil temperature auto control, auto cycle enriching valve, industry electric power control valve, water temperature regulating valve, safety device, space heating, fire protection, air filtering, temperature regulating device, sanitary ware and heating temperature controlling valve, air temperature control, ventilating control, solar water heater, automatic door and window, thermal driving electric switch, alarm apparatus, house ventilating, radiator temperature control valve, hot landing device for aviation and automaton etc.
Within temperature control range of –20 ~ 180 ℃ of Thermostatic Wax may compound with different temperature range and different efficient distance according to client’s technical demand. Our company may offer the relative technical service.
|
Model Number |
Appearance (Normal Temperature) |
Quality Standard |
|||
|
Range of Temperature Control |
Effective Distance Travel |
Water-Solubility sAcid and Alkali |
Mechanical Impurity |
||
|
B-5-1 |
Liquid |
-20/-5 |
≥7 |
Non. |
Non. |
|
B0-1 |
Liquid |
-15/0 |
≥7 |
Non. |
Non. |
|
B5-1 |
Liquid |
-10/5 |
≥7 |
Non. |
Non. |
|
B15-1 |
Liquid |
0/15 |
≥7 |
Non. |
Non. |
|
B20-1 |
Semisolid |
5/20 |
≥7 |
Non. |
Non. |
|
B25-1 |
Semisolid |
10/25 |
≥7 |
Non. |
Non. |
|
B30-1 |
Semisolid |
15/30 |
≥7 |
Non. |
Non. |
|
B35-1 |
Semisolid |
20/35 |
≥7 |
Non. |
Non. |
|
B40-1 |
Powder, Slice , Column |
25/40 |
≥7 |
Non. |
Non. |
|
B45-1 |
Powder, Slice , Column |
30/45 |
≥7 |
Non. |
Non. |
|
B50-1 |
Powder, Slice , Column |
35/50 |
≥7 |
Non. |
Non. |
|
B55-1 |
Powder, Slice , Column |
40/55 |
≥7 |
Non. |
Non. |
|
B60-1 |
Powder, Slice , Column |
45/60 |
≥7 |
Non. |
Non. |
|
B65-1 |
Powder, Slice , Column |
50/65 |
≥7 |
Non. |
Non. |
|
B70-1 |
Powder, Slice , Column |
55/70 |
≥7 |
Non. |
Non. |
|
B75-1 |
Powder, Slice , Column |
60/75 |
≥7 |
Non. |
Non. |
|
B80-1 |
Powder, Slice , Column |
65/80 |
≥7 |
Non. |
Non. |
|
B85-1 |
Powder, Slice , Column |
70/85 |
≥7 |
Non. |
Non. |
|
B90-1 |
Powder, Slice , Column |
75/90 |
≥7 |
Non. |
Non. |
|
B95-1 |
Powder, Slice , Column |
80/95 |
≥7 |
Non. |
Non. |
Product detail pictures:
Being supported by an advanced and professional IT team, we could offer technical support on pre-sales & after-sales service for 2017 Good Quality Thermostatic Wax Linearity Series Export to America, The product will supply to all over the world, such as: Boston , United States , Russia , Our aim is to help customers realize their goals. We are making great efforts to achieve this win-win situation and sincerely welcome you to join us. In a word, when you choose us, you choose a perfect life. Welcome to visit our factory and welcome your order! For further inquiries, please do not hesitate to contact us.
Test of 7 piezo electric bimorph cantilever beam actuators at 1 Hz, 0-300V. These are wired in parallel and held with ceramic tweezers to prevent shorting.
The bimorph actuators are a laminate consisting of three layers: the top layer is PZT, the middle layer is carbon fiber, and the bottom layer is PZT. They can be thought of as two capacitors in series; on the top side, the PZT-to-carbon fiber represents one capacitor, while the carbon fiber-to-PZT represents the second capacitor on the bottom side. The ‘directionality’ or poling of the PZT depends on the manufacture of the PZT material – meaning that the electric field applied to them should always be in the direction of their alignment (you can’t simply put an AC waveform to them). These actuators are configured to run in “simultaneous drive”, which means that the top-most surface of the top PZT layer is charged at a constant ‘bias’ voltage, the bottom-most pzt surface is held at ground potential, and the carbon fiber layer is given a varying signal in this case a 1Hz sinusoid from 0V to 300V. This arrangement ensures that the signal applied to each ‘capacitor’ unit is always positive. For example, if at one moment the ‘bias’ was 300V and the and carbon fiber was at 150V, then each capacitor would be strained the same amount and the actuator as a whole would be in a neutral position. On the other hand, if the bias was 300V and the carbon fiber layer was held at 50V, then the top PZT would be more strained than the lower PZT, causing the actuator to deflect. In both cases, the polarity of each ‘capacitor’ is respected. There are different types of arrangements for driving actuators, such as the ‘alternating drive’ topology.
AT1200 high strength Stainless Steel Belt for Double Cooling Steel Belt Flaking Machine to make Sulphur, Wax, Resin, Paraffin, Gelatin flakes
we are STEEL BELTs manufacturer & exporter from China.
We adopt Japanese prime steel material & European belt technology & knowhow.
Contact: Vijay Shen | Foreign Trade Manager
Email 1: sales@mingkebelt.com
Email 2: steelbeltchina@gmail.com
Skype: SteelBeltChina
Mob/WhatsApp: +86 13072182825
Website: https://www.mingkebelt.com
Alibaba: https://www.mingkebelt.en.alibaba.com
Facebook: https://www.facebook.com/steelbeltchina
LinkedIn: https://www.linkedin.com/company/shanghai-mingke-process-systems-co.-ltd.
Homepage: https://www.steelbelt.jimdo.com
Shanghai Mingke Process Systems Co.,Ltd. is specialized in supplying special high strength steel belts and services.
We focus on manufacturing & providing high tensile strength steel belts, especially supply super wide steel belt (max. width reaches 9 meters), precipitation hardening treated steel belt and super mirror steel belt.
We provide MT1650 (previous 1650SM) / MT1500 (previous 1500SM) Martensitic Stainless Steel Belt, AT1200 (previous 1200SA) / AT1000 (previous 1000SA) / DT980 Austenitic Stainless Steel Belt and CT1300 (previous 1300C) / CT1100 (previous 1100C) DT1320 Carbon Steel Belt. We also manufacture Double Belt Press for composite material board by ourselves.
Mingke steel belts are applicable for various industries & systems, such as: Composite Material Board Industry (Double Belt Press), Chemical Industry (Single / Double Belt Flaker & Pelletizer), Woodworking Wood Based Panel Industry (Double Belt Press & Mende), Rubber Industry (Vulcanizer / Rotocure), Food Industry (Bake Oven & Quick Frozen Food Conveying), Film Casting Industry (Super Mirror Steel Belt), Conveyor Systems (Conveyor & Sorter) and Papermaking Industry, etc.
Our steel belt services contain Longitudinal Welding, Cross Welding, Welding Area Heat Treatment, Crack Repair, Quick Disc, Shot Peening, V-rope Bonding, etc.
We Not Only Produce Steel Belts, But Also Deliver Artisan Spirit!
Mingke steel belt Models:
1. MT1650 (previous 1650SM)
2. MT1500 (previous 1500SM)
3. AT1200 (previous 1200SA)
4. AT1000 (previous 1000SA)
5. CT1300 (previous 1300C)
6. CT1100 (previous 1100C)
7. DT1320
8. DT980
Mingke steel belt Measurements:
1. Length — customized
2. Width — 1000 / 1200 / 1550 / 2000 / 3000 / 4000 … 9000 mm
3. Thickness — 1.0 / 1.2 / 1.8 / 2.2 / 2.7 / 3.0 … mm
Mingke steel belt SUS No.:
SUS301, SUS304, SUS316, SUS630, SUS632, etc.
Steel belt, steel belt supplier, steel belt China, food belt, oven belt, bake oven belt, rubber curing machine belt, rotocure belt, chemical belt, sulphur belt, resin cooler belt, pelletizer belt, wax cooling belt, composite panels press, double belt press belt, double belt press, single belt press, MDF board belt, particle board press belt, super mirror steel belt, industrial belt, conveyor belt, sorter belt, Sandvik, Mingke, Berndorf, Naut, Nacon, contiroll belt, CPS steel belt, HDF panels belt, carbon steel belt, food grade belt, stainless steel belt
Contact: Vijay Shen | Foreign Trade Manager
Email 1: sales@mingkebelt.com
Email 2: steelbeltchina@gmail.com
Skype: SteelBeltChina
Mob/WhatsApp: +86 13072182825
Website: https://www.mingkebelt.com
Alibaba: https://www.mingkebelt.en.alibaba.com
Facebook: https://www.facebook.com/steelbeltchina
LinkedIn: https://www.linkedin.com/company/shanghai-mingke-process-systems-co.-ltd.
Homepage: https://www.steelbelt.jimdo.com
