Professional High Quality TU-025 thermostatic cartridge wax sensor for sanitary ware Supply to Jamaica
Short Description:
Product Detail
Product Tags
Professional High Quality TU-025 thermostatic cartridge wax sensor for sanitary ware Supply to Jamaica Detail:
1. Operation Principle
The Thermostatic Wax that has been sealed in shell body induces expansion by a given temperature, and inner rubber seal part drives its handspike to move under expansion pressure to realize a transition from thermal energy into mechanical energy. The Thermostatic Wax brings an upward movement to its handspike, and automatic control of various function are realized by use of upward movement of handspike. The return of handspike is accomplished by negative load in a given returned temperature.
2. Characteristic
(1)Small body size, occupied limited space, and its size and structure may be designed in according to the location where needs to work.
(2)Temperature control is reliable and nicety
(3)No shaking and tranquilization in working condition.
(4)The element doesn’t need special maintenance.
(5)Working life is long.
3.Main Technical Parameters
(1)Handspike’s height may be confirmed by drawing and technical parameters
(2)Handspike movement is relatives to the temperature range of the element, and the effective distance range is from 1.5mm to 20 mm.
(3)Temperature control range of thermal wax actuator is between –20 ~ 230℃.
(4)Lag phenomenon is generally 1 ~ 2℃. Friction of each component part and lag of the component part temperature cause a lag phenomenon. Because there is a difference between up and down curve of traveling distance.
(5)Loading force of thermal wax actuator is difference, it depends on its’ shell size.
Product detail pictures:
We can normally fulfill our respected consumers with our great excellent, great value and good provider due to we're much more specialist and extra hard-working and do it in cost-effective way for Professional High Quality TU-025 thermostatic cartridge wax sensor for sanitary ware Supply to Jamaica, The product will supply to all over the world, such as: Slovakia , Greenland , Bolivia , In the new century, we promote our enterprise spirit "United, diligent, high efficiency, innovation", and stick to our policy"basing on quality, be enterprising, striking for first class brand". We would take this golden opportunity to create bright future.
Tutorial explaining how to replace the thermostat housing assembly, water pump and coolant drain and fill for an E46 series BMW. The specific video here is a 2002 330xi sedan that had a water pump that was beginning to weep coolant from the main shaft of the water pump. The video shows all the steps necessary to remove all related items on the engine and engine bay to access and properly remove and replace the cooling system components. The BMW parts department advised that I also change the thermostat housing assembly when doing the water pump because an old thermostat could risk failure without a moments notice. The thermostat and water pump and coolant were all purchased directly from BMW. Coolant was mixed using distilled water in a 60/40 solution mixed which I confirmed it’s freeze and boiling points using a widely available coolant tester made by Prestone. 1 4 litre jug of coolant or antifreeze (as some call it) can make up to a maximum of 8 litres of coolant mixed at a 50/50 to water ratio. I opted to make a 60/40 because in Canada our climate occasionally CAN dip to 34 degrees Celsius below 0.
It is worth mentioning that doing a water pump replacement on a manual transmission based E46 is easier than one that has an automatic transmission because the cooling fan on the manual transmission 3 series BMWs use an electric cooling fan whereas the automatics use a hydraulically coupled fan clutch assembly that bolts onto the reverse threaded shaft of the water pump. IF you have an automatic transmission E46 then you will NEED to invest in a fan clutch holding tool specific to the E36 and E46 BMWs and a slim profile 32mm wrench to “reverse unscrew” the fan clutch off of the water pump. Not necessarily difficult to do BUT a little more work is involved plus the cost of buying the special tool. Everything else mentioned in this tutorial is otherwise the same.
It is also advisable that since you’re removing everything out of the front of the engine that you replace both the serpentine drive belt and the a/c drive belt at the same time.
The motor in my car is a 3.0 inline 6 cylinder M54B30 engine
BMW Parts #’s
11-51-7-527-910 (Water pump) replaces old part # BM11-51-7-503-884
11-53-7-509-227 (Thermostat housing)
83-51-9-415-964 (Engine coolant)
I tear into the coolant system and show what’s behind those mysterious bolts. My 93 rx7 is going through a single turbo conversion and I want to share my findings.
