Reliable Supplier TU-1C05 thermal wax actuator for thermostatic automatic water drain valve for Turkmenistan Factories

Reliable Supplier
 TU-1C05 thermal wax actuator for thermostatic automatic water drain valve for Turkmenistan Factories

Short Description:

Product Detail

Product Tags

With our loaded practical experience and thoughtful solutions, we now have been identified for a trusted provider for numerous intercontinental consumers for Thermal Or Magnetic Actuator , Automatic Temperature Control Washing Machine , Automatic Temperature Control Bath Faucet , Our tenet is "Reasonable prices, efficient production time and best service" We hope to cooperate with more customers for mutual development and benefits.
Reliable Supplier TU-1C05 thermal wax actuator for thermostatic automatic water drain valve for Turkmenistan Factories Detail:

1. Operation Principle

The Thermostatic Wax that has been sealed in shell body induces expansion by a given temperature, and inner rubber seal part drives its handspike to move under expansion pressure to realize a transition from thermal energy into mechanical energy. The Thermostatic Wax brings an upward movement to its handspike, and automatic control of various function are realized by use of upward movement of handspike. The return of handspike is accomplished by negative load in a given returned temperature.

2. Characteristic

(1)Small body size, occupied limited space, and its size and structure may be designed in according to the location where needs to work.

(2)Temperature control is reliable and nicety

(3)No shaking and tranquilization in working condition.

(4)The element doesn’t need special maintenance.

(5)Working life is long.

3.Main Technical Parameters

(1)Handspike’s height may be confirmed by drawing and technical parameters

(2)Handspike movement is relatives to the temperature range of the element, and the effective distance range is from 1.5mm to 20 mm.

(3)Temperature control range of thermal wax actuator is between –20 ~ 230℃.

(4)Lag phenomenon is generally 1 ~ 2℃. Friction of each component part and lag of the component part temperature cause a lag phenomenon. Because there is a difference between up and down curve of traveling distance.

(5)Loading force of thermal wax actuator is difference, it depends on its’ shell size.

 

 


Product detail pictures:

Reliable Supplier
 TU-1C05 thermal wax actuator for thermostatic automatic water drain valve for Turkmenistan Factories detail pictures


With this motto in mind, we've got become among essentially the most technologically innovative, cost-efficient, and price-competitive manufacturers for Reliable Supplier TU-1C05 thermal wax actuator for thermostatic automatic water drain valve for Turkmenistan Factories, The product will supply to all over the world, such as: Madras , Brasilia , Danish , "Good quality, Good service " is always our tenet and credo. We take every effort to control the quality, package, labels etc and our QC will check every detail during producing and before shipment. We have been willing to establish long business relationship with all those who seek the high quality products and good service. We've got set up a wide sales network across European countries, North of America, South of America, Middle East, Africa, East Asia countries.Please contact us now, you will find our expert experience and high quality grades will contribute to your business.



  • I need your assistance with Rheem water heater troubleshooting.

    If you do not have hot water, check the circuit breaker to the hot water heater.

    I have electricity.

    Yeah, but a breaker flipped off or a blown panel fuse will turn off the power.

    It is on.

    I’m also assuming the high limit switch on the unit is not tripped. That’ll kill it.

    The lights on the control panel are on, so it seems to be on. If the high limit switch kicked in, I’d expect at least a couple red lights.

    The thermostat could be set too low.

    This is not like the house thermostat; we don’t have thermostat wars over the hot water level, especially when you can up the percentage of cold water if you don’t like it.

    If you cannot get much hot water even on all hot, the thermostat may not be functioning or it isn’t seated properly.

    I cannot believe it has been moved, and it is not like it could have fallen off while someone was dusting it.

    The wiring could be loose.

    Unless there are rats in there, nothing would have gotten it loose. And a colony of dust bunnies won’t even cause a problem except an asthma attack when you open it.

    It could break due to thermal stresses, warming and cooling.

    A hot water heater usually just stays hot.

    If the heating elements burned out, it would not get hot. Well, it gets just lukewarm or hot for the portion around the remaining work element until the second one burns out.

    I’d have to ask a repair man to do that because I do not want to make a mess draining it to change out an element.

    In theory, a lot of sediment in it could cover the elements and cause it not to work right, especially if the sediment coats the thermostat so that it doesn’t read right.

    So I need to clean the water tank out so that it works right.

    A lot of sediment on the bottom can cause bubbling and popping as hot water boils and escapes through the mud on the bottom.

    I think the noise in the basement is the water softener, not the hot water heater.

    If you have a gas water heater, the gas valves may need to be cleaned periodically of rust and ash, or the electrical sparker for the gas may need to be replaced.

    I know a flame sensor coated in ash will cause it to not recognize the flame is burning and kill it. But I do not have a gas hot water heater.

    Then the unit not heating up isn’t due to poor gas supply. It could still be due to humidity or a leak shorting out electrical connections.

    At that point, I do not know if I need a plumber or electrician.



    This is a short demonstration for the setup of ROBONET and RC Software from IAI.

    http://www.intelligentactuator.com/robonet-network-controller/

    ROBONET allows you to control multiple electric actuators with one single communication port, the gateway unit. With both field network and serial communication port, user can choose either one to send their commands to the controller, and thus controls the actuator.
    In this tutorial, we are only focusing on basic introduction of each ROBONET unit, setup, and use RC Software on the PC through serial communication port to program position table of each ROBONET controller.

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Plane

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Star

    WhatsApp Online Chat !